Clarity banner

 Gemological Institute of  America's Clarity Standards


FL
Flawless, no inclusions or blemishes of any sort under 10x magnification.
IF
Internally flawless, no inclusions and only insignificant blemishes under 10x.
VVS1  - VVS2
Inclusions are difficult to  locate or see under 10x.
VS1  - VS2
Inclusions present less difficulty to located or see under 10x.
SI1  - SI2
Inclusions are readily seen at 10x, although they remain invisible to the unaided eye when the diamond is viewed face up.
I1
One or more inclusions or their effect; can be seen by the unaided eye.
I2
Inclusions are easily visible to the unaided eye.
I3
Inclusions are so obvious and  large that they affect both brilliancy and beauty of the diamond.


 Flawless (FL)


A flawless diamond shows no inclusions or blemishes of any sort when observed by a skilled grader under 10x magnification. To establish a stone as flawless, GIA Gem Trade Laboratory graders examine it with both a microscope and a loupe.The following conditions will still qualify as stone as flawless:
* Extra facets on the pavilion which cannot be seen when the stone is viewed
 face-up.
* Small naturals confined to the width of the girdle (unless the girdle is thick).
* Internal graining which is neither reflective, whitish, colored, nor significantly
affecting transparency.
How much naturals should influence the clarity grade of a diamond  is a matter of opinion. Opinions range from those who think that any natural excludes a stone from flawless or even internally flawless to those who accept naturals of almost any size in the  flawless classification.

GIA takes a "middle-of-the-road" position: If a natural is small enough to be confined within the width of the girdle  (except when the girdle is thick) and does not affect the symmetry  of the stone by creating a flat spot or indentation, it is considered  an identintifying characteristic and does not influence the clarity grade. If, on the other hand, the natural flattens or indents the girdle outline, or can be seen when the stone is viewed face-up, it does affect the grade.


 Internally Flawless (IF)


This grade applies to diamonds which have no inclusions, but do have some minor surface blemishes. Characteristics such as surface grain lines, naturals, and extra facets on the crown, render a diamond internally flawless rather than flawless. Diamonds classified as internally flawless must be free from any internal imperfection when examined by a skilled diamond grader using 10x magnification. Blemishes that can be removed by minor repolishing separate the internally flawless from the flawless grade. The one exception is a diamond that reveals minor surface grain lines which ordinarily can not be removed by repolishing.
 

 Very Very Slightly Included (VVS1, and VVS2)


 These grades describe diamonds which contain minute inclusions that are difficult even for skilled graders to see under 10x magnification. An example of VVSI might be a minute pinpoint  or hairline feather or perhaps a pinpoint or two visible under the bezel facet. To keep the VVS grades in perspective, it should be noted that they represent the top clarity grade carried by most suppliers and retail jewelers. The VVS grades have often  been and still are, presented as flawless or perfect diamonds with no intent to misrepresent by wholesalers and retailers simply because such minute inclusions are difficult to see. Reflective internal graining, bearded girdles, minor bruises, tiny cavities, etc., would be sufficient to grade the stones as VVS1 or VVS2, depending upon degree.

 

 Very Slightly Included (VS1, and VS2)


Although inclusions are clearly visible under 10x magnification  in the VS grades, they are characterized as minor or small in appearance. Diamonds in these grades might have characteristics  such as small included crystals, small clouds, small feathers, or several pinpoints. The inclusions in these grades do not affect the beauty or the durability of the stone.

 

 Slightly Included (SI1, and SI2)


These grades describe stones in which the inclusions are noticeable or fairly easy to see under 10x magnification. Typical characteristics include clouds, included crystals, knots, chips, pits, cavities, and feathers. Usually none are visible when the stones are viewed  with the unaided eye.

 

 Imperfect (I1, I2, and I3)


These grades include diamonds with inclusions which are obvious under 10x magnification or can be seen with the unaided eye, and those that have inclusions, such as large cleavages, large included crystals surrounded by feathers that seriously influence durability. These grades also include diamonds in which the inclusions are so numerous that they affect transparency and brilliance.

I3, the bottom category, includes diamonds that lack transparency and those with large cleavages and dark inclusions easily visible to the unaided eye. They are actually borderline industrial stones; whether they are graded as industrial or gem quality depends  on market demand.

A large stone with an eye-visible inclusion at or near the girdle may not warrant an I grade, because the inclusion could be removed with much less loss of value than an I grade  would suggest. When appraising, some diamond experts grade such stones as I's, but value them on the basis of the recut grade  and lower weight they would have if the inclusion were removed.   

Back to the 4 C's
KFA